热处理对Ti-Al-Sn-Zr-Mo-Si-X系合金性能的影响

研究了热处理对3种Ti-Al-Sn-zr-Mo-Si-X（X为ⅤB，ⅥB族一种或几种元素）系合金（A、B、C）室温拉伸性能的影响，对优化合金的热处理制度及优选热处理制度下3种合金的疲劳裂纹扩展行为也进行了探讨。结果表明，优选热处理制度下A、C合金的裂纹扩展速率差别不大，B合金560℃时效处理后，裂纹扩展速率比540℃时效处理的小。在相同热处理制度下，比较3种合金裂纹扩展速率的结果表明，IgΔK在1．2～1．5范围内B合金的抗疲劳裂纹扩展性能较优。     

应变速率对中碳低温贝氏体钢强塑性的影响

摘要：为探索低温贝氏体钢的断裂行为,研究应变速率对低温贝氏体钢TRIP效应的影响,采用不同应变速率的拉伸试验对低温贝氏体钢的强塑性进行研究。利用扫描电镜（SEM）、透射电镜（TEM）及X射线衍射（XRD）等试验方法对低温贝氏体钢的微观组织、断口形貌及裂纹走向进行表征。结果表明,随着应变速率的提高,试验钢的屈服强度由771MPa上升至806MPa,抗拉强度由1554MPa上升至1606MPa,断后伸长率由13.5%下降至9.0%。主要原因是高应变速率拉伸引发的绝热温升抑制了残余奥氏体的马氏体相变,对试验钢塑性造成负面影响。     

在线监测结晶器调宽换向阀阀芯卡阻方法的实现

对某炼钢厂铸机结晶器在线调宽液压系统的工作原理进行了分析,并重点分析了调宽过程中换向阀阀芯卡阻的问题,针对该问题对其液压系统进行了改进,改进后可以在线监测换向阀阀芯是否卡阻。该改进的实施在减少结晶器在线调宽时发生漏钢故障方面起到了重要作用。     

300M钢腐蚀疲劳裂纹萌生的超载特性

本文对３００Ｍ钢在空气与３．５％ＮａＣｌ溶液中疲劳裂纹萌生的周期超载和单次超载特性进行了试验研究与理论分析。试验结果表明，３．５％ＮａＣｌ溶液中，单次超载所致腐蚀疲劳裂纹迟滞萌生的迟滞强度远小于周期超载的对应值。３．５％ＮａＣｌ溶液与空气中，超载迟滞强度均随超载比增大或等效应力幅水平的提高而增大，在腐蚀疲劳裂纹萌生寿命估算中，只考虑单次超载的迟滞规律，会得出大大保守的寿命估计，只有将单次超载和周期     

CREEP CRACK PROPAGATION IN CONVENTIONAL CAST AND DIRECTIONALLY SOLIDIFIED SUPERALLOY RENE 80

The creep crack propagation in superalloy René80 of two different microstructures,i.e.,equiaxed grain structure by conventional casting and columnar grain by directionalsolidification,was investigated under static load at 1123 K.The creep crack growth rate,da/dt,seems to be correlated with the stress intensity factor,K.The creep crack growth ratein the directionally solidified alloy is lower than that in the conventional cast alloy,owing tothe elimination of transverse grain boundaries.The effect of microstructure on creep crackpropagation has also been discussed.     

IN-SITU OBSERVATION OF CRACK TIP DEFORMATION IN A DUPLEX STAINLESS STEEL

The development of dislocation structures in the plastic zone ahead of a crack tip has been in-vestigated in a duplex stainless steel during in-situ deformation experiments in a scanningtransmission electron microscope.It was found that the dislocation distribution wassignificantly different in the ferrite and in the austenite.In the ferrite grains,the dislocationsemitted by the crack tip may cross-slip out of the original slip planes and form a broad plasticzone.However,in the austenite,the dislocation free zone is small and the dislocations emittedby the crack pile up in its slip plane.The selection of slip systems at the crack tip depends onthe crack tip Schmid factors in both phases.But after large deformation,the selection of thesecond slip systems at the craek tip in austenite does not depend on the Schmid factors.     

A fatigue-life prediction methodology for notched aluminum-magnesium alloy in gulf seawater environment

Local-strain and linear-elastic fracture-mechanics (LEFM) methodologies have been investigated for prediction of the corrosion-fatigue life of notched components of specially developed Al-2.5Mg alloys exposed to Arabian Gulf seawater environment. Corrosion-fatigue crack initiation life estimates were obtained using strain-life relationships; corrosion-fatigue crack propagation life estimates were obtained using LEFM relationships. The total corrosion-fatigue life was considered to be the sum of the crack initiation and crack propagation lives. Estimated corrosion-fatigue lives were compared with experimentally obtained corrosion-fatigue life data using center-notched specimens of three types of Al-2.5Mg alloys (containing different amounts of chromium) exposed to Arabian Gulf seawater environment. Two notch geometries, a circular notch (K _t= 2.42) and an elliptical notch (K _t= 4.2), were investigated. Good corrosion-fatigue life predictions can be obtained using local-strain and LEFM methodologies by determining the relevant material constants via a few simple fatigue tests on smooth specimens and a few crack-growth-rate tests in the environment at the frequency of interest.     

冲天炉炉胆的(径向)胀裂问题及其防止措施

冲天炉炉胆径向胀裂问题，也是一道颇有难度的课题，本文提出：用平行四边形、竖立的梯形和微凹矩形三种炉壁断面作为防止措施。     

高强度钢焊接裂纹检测及其成因分析

为了充分认识高屈强比、高强度低温材料焊接裂纹的敏感性，通过对NK—HIT—EN610U2L低合金高强度钢球罐支柱角焊缝裂纹的检测、解剖对比和成因分析，发现焊缝外表面缺陷与内部焊接缺陷存在一定关系，高应力设计部位比较突出，因此检测与焊接要引起高度注意。     

大型弹簧钢片开裂原因分析

为保证大型弹簧钢片在热处理过程中，不发生开裂和翘起度超差，重新制订了热处理工艺。通过增加高温回火、降低淬火温度、加快冷却速度等手段，获得了最好的效果。